Tools: Hypercube 300 - Revision history

Jonadair: gone (for now) but may return

2022-06-23T18:39:53Z

gone (for now) but may return

← Older revision		Revision as of 18:39, 23 June 2022
Line 18:		Line 18:
	* We brought the bed all the way down, loosened the Z motor mounts and let everything pull itself into natural alignment then tightened everything up.		* We brought the bed all the way down, loosened the Z motor mounts and let everything pull itself into natural alignment then tightened everything up.

			[[Category:Gone]]

			<!--
	[[Category:Tools]]		[[Category:Tools]]
	[[Category:Fabrication]]		[[Category:Fabrication]]
	[[Category:3D Printing]]		[[Category:3D Printing]]
			-->

2022-06-23T18:35:58Z

← Older revision		Revision as of 18:35, 23 June 2022
Line 1:		Line 1:
	~~Last revision {{REVISIONTIMESTAMP}} by {{REVISIONUSER}}~~
			<span style="background-color:#fef6e7; border: 1px solid #fc3; padding:8px;>Offline / offsite</span>


	== Accessing the Hypercube ==		== Accessing the Hypercube ==

2019-11-18T00:23:24Z

← Older revision		Revision as of 00:23, 18 November 2019
Line 15:		Line 15:
	* The Z motors were a little out of alignment with the z lead screw nuts on the best. It ran fine at the top of its range because the lead screws are unsupported up there and that masks the alignment problem. At the bottom of its movement range everything is bolted to the frame and the slight misalignment cause binding that the Z stepper motors could not overcome.		* The Z motors were a little out of alignment with the z lead screw nuts on the best. It ran fine at the top of its range because the lead screws are unsupported up there and that masks the alignment problem. At the bottom of its movement range everything is bolted to the frame and the slight misalignment cause binding that the Z stepper motors could not overcome.
	* We brought the bed all the way down, loosened the Z motor mounts and let everything pull itself into natural alignment then tightened everything up.		* We brought the bed all the way down, loosened the Z motor mounts and let everything pull itself into natural alignment then tightened everything up.

			[[Category:Tools]]
			[[Category:Fabrication]]
			[[Category:3D Printing]]

2018-07-28T02:06:42Z

Accessing the Hypercube: Added url

← Older revision		Revision as of 02:06, 28 July 2018
Line 2:		Line 2:

	== Accessing the Hypercube ==		== Accessing the Hypercube ==
	* From within the Tampa Hackerspace network, the Hypercube #1 can be accessed by browsing to ~~_____________~~		* From within the Tampa Hackerspace network, the Hypercube #1 can be accessed by browsing to http://hypercube1/
	* Remotely, printer status can be viewed by logging in to THS's Slack and viewing the #3d_printer_status channel.		* Remotely, printer status can be viewed by logging in to THS's Slack and viewing the #3d_printer_status channel.

2018-07-28T01:35:54Z

Initial writeup; problem#1; This sucks

← Older revision		Revision as of 01:35, 28 July 2018
Line 1:		Line 1:
	~~Placeholder for Hypercube 300~~

	Last revision {{REVISIONTIMESTAMP}} by {{REVISIONUSER}}		Last revision {{REVISIONTIMESTAMP}} by {{REVISIONUSER}}

			== Accessing the Hypercube ==
			* From within the Tampa Hackerspace network, the Hypercube #1 can be accessed by browsing to _____________
			* Remotely, printer status can be viewed by logging in to THS's Slack and viewing the #3d_printer_status channel.

			== Building the Hypercube ==
	Hypercube 300....and it uses CoreXY motion mechanics.		Hypercube 300....and it uses CoreXY motion mechanics.


			== Problems we've encountered ==

			=== Hypercube bed is all the way down and does not want to move ===
			Resolution by @adrianm1972:
			* The Z motors were a little out of alignment with the z lead screw nuts on the best. It ran fine at the top of its range because the lead screws are unsupported up there and that masks the alignment problem. At the bottom of its movement range everything is bolted to the frame and the slight misalignment cause binding that the Z stepper motors could not overcome.
			* We brought the bed all the way down, loosened the Z motor mounts and let everything pull itself into natural alignment then tightened everything up.

2018-07-03T23:42:01Z

Added Last revision.

← Older revision		Revision as of 23:42, 3 July 2018
Line 1:		Line 1:
	Placeholder for Hypercube 300		Placeholder for Hypercube 300

			Last revision {{REVISIONTIMESTAMP}} by {{REVISIONUSER}}


	Hypercube 300....and it uses CoreXY motion mechanics.		Hypercube 300....and it uses CoreXY motion mechanics.

2018-06-15T23:05:14Z

← Older revision		Revision as of 23:05, 15 June 2018
Line 1:		Line 1:
	Placeholder for Hypercube 300		Placeholder for Hypercube 300



			Hypercube 300....and it uses CoreXY motion mechanics.

2018-06-15T22:37:27Z

Created page

New page

Placeholder for Hypercube 300